Definitions: Wireless & WiFi Terms

Wireless and WiFi Definitions:

WiFi: Data-Alliance.net

Access Point (Wireless Access Point): Often referred to as a "wireless router:" Stationary radio station that has a connection to the Internet. Other names for the Wi-Fi Access Point are: Access Point, AP, or Base Station. There are many different types of Access Point. At the high end of the range are commercial grade installations operated by Marina’s, Telephone companies etc. At the medium end are libraries, cafes, and smaller businesses. Finally, there are low systems operated by private individuals largely to provide wireless coverage for their homes. Some Access Points are open access; others are more protected and require some form of password entry. Some Access Points are free; others require some form of payment. The important thing to know is that with good client-side WiFi equipment, one has a larger choice of what Access Points to connect with. This often eliminates the need for paid access.

Bridge (wireless bridge /WiFi bridge): Converts a Wi-Fi connection to an Ethernet port, for standard network-cable connection to any PC with a network interface card (NIC) or to another network device with Ethernet ports, such as a network printer or network switch/hub. Another way of stating this is that a Wi-Fi bridge connects your “wired” LAN to a WiFi network. The wired and WiFi LAN thus connected must use the same IP address configuration (usually passed through the bridge automatically via DHCP).

Definitions types of Coaxial Antenna Cable Assemblies & Connectors:

Fresnel Zone: An electromagnetic phenomenon, in which light waves or radio signals get diffracted or bent from solid objects near their path. The radio waves reflecting off the objects may arrive out of phase with the signals that traveled directly to the receiving antenna thus reducing the power of the received signal. Therefore you have to have more than visual line-of-sight: You need for the Fresnel zone to be clear or the obstructions will block part of your throughout - you will have lower rate of through-put.

Signal Strength: RSSI: Received Signal Strength Indication: Measured from 0 to -100, generally, though RSSI has no standard units for all vendors: Generally the higher (closer to 0) the better, and the closer to -100 the worse.

SNR: Signal-to-Noise Ratio and Noise Floor: SNR is not actually a ratio but the difference in decibels between the received signal and the background noise level (noise floor). For example, if a radio (client device) receives a signal of -75 dBm and the noise floor is measured at -90 dBm, the SNR is 15 dB. Data corruption and therefore re-transmissions will occur if the received signal is too close to the noise floor. Re-transmissions adversely affect throughput and latency.

Noise Floor: Use a spectrum analyzer to determine the noise floor: Ubiquiti's AirView spectrum analyzer is built-in to all AirMax equipment: Noise Floor is easily found by looking at the Waterfall View - the legend in the upper right corner: The number to the far-left in this legend is always adjusted to the calculated noise floor (and the high end [right] is fixed at the highest detected power since the start of the session).

MCS: Modulation and Coding Scheme - MCS Index Values: Modulation and Coding Scheme (MCS) Index Values can be used in conjunction with channel width values to allow you to instantly calculate the available data rate of your wireless hardware.

  • The MCS index value list gives every combination of "number of spatial streams + modulation type + coding rate" that is possible. In practice the achievable MCS value will depend on a large number of variables, and it may be prudent to run your hardware at a lower MCS value on purpose in order to allow for adequate fade margin in your link.
  • The MCS value will only tell you the 'over the air' data rate of a link and not tell you what the actual usable throughput will be. You will need to refer to the documentation of your hardware for this information.

PHY Rate (Link Rate) compared to Throughput (Transfer Speed): Difference between wireless link rate, actual file transfer and web browsing speed:

  • The wireless link rate is sometimes called the physical layer (PHY) rate. It is the maximum speed that data can move across a wireless link between a wireless client and a wireless access point or bridge.
  • User activities like file transfer and web content browsing happen at the application layer. The rate obtained at the application layer is much lower than the physical layer rate. In fact, a link rate of "300 Mbps" usually corresponds to 50 to 90 Mbps speed on the TCP/UDP layer.

Posted by George Hardesty on 2nd Nov 2022


RP-SMA cables and adapters SMA antenna cables and adapters N-type cables and adapters U.FL cables MHF4 Cables MMCX cables
GPS antennas Signal-loss (attenuation) in LMR-100 and LMR-200 cables BNC cables RP-TNC cables and adapters Vehicle Antennas Top Tips for Long Range WiFi
Through-hole antenna mounts L-Mounts for Antennas:  Mount on Pole or Wall Adhesive Mount Antennas Combination Antennas LTE GPS WiFi Bluetooth 4G 3G Cable Glands Roof Mounts for Antennas